Точная резка солнечных фотоэлектрических панелей с алмазной проволочной петлей: 10 мм Тестовые данные
Sample testing for a European client (Company N) · Ring diamond wire cutting process
Обзор
This report documents the precision slicing of solar photovoltaic (ПВ) panels using a ring diamond wire cutting system. The evaluation covers equipment and wire selection, cutting methodology, параметры процесса, and the resulting dimensional accuracy, surface quality, and edge integrity of the sliced wafers. Test results indicate that the combination of a gantry-type ring diamond wire machine, water-based cooling, and appropriately matched process parameters delivers stable, high-precision straight slicing of PV panel stock.
1. Test Specimen
| Параметр | Значение |
|---|---|
| Материал | Solar photovoltaic (ПВ) panel |
| Твёрдость | approx. 4–5 Mohs |
| Размеры заготовки | 55 мм × 20 мм × 10 миллиметр |
| Target slice thickness | 10 миллиметр |
2. Выбор оборудования и проволоки
Equipment: ESO-GM. Given the material characteristics of solar PV panels and the requirement for high-precision straight cutting at a 10 Толщина слоя, мм, Ensoll selected the ESO-GM gantry-type ring diamond wire cutting system. The gantry configuration maintains running stability and trajectory accuracy throughout the cut, reducing the influence of machine vibration and fluctuations in cutting load on slice quality.
Охлаждающая жидкость: water-based cutting. Water is used as the cooling medium. It cools the contact zone between the diamond wire and the PV panel and carries away part of the heat and debris generated during cutting. This limits localised heat accumulation and debris retention, reduces fluctuation in cutting load, and helps suppress chipping, micro-cracking, and dimensional deviation.
Проволока: fully plated. A fully plated diamond wire was selected. The plated construction improves the bonding strength between the diamond abrasive grains and the wire core and provides a more uniform grain distribution. This sustains a continuous and stable material removal rate, reduces grain pull-out and wire wear, and contributes to lower chipping, micro-cracking, and dimensional variation in the sliced PV panels.
3. Cutting Method and Equipment Advantages
Gantry cutting configuration. The gantry structure provides high overall rigidity and running stability. The top-down vertical feed helps maintain a stable wire trajectory and reduces the effect of machine vibration and motion error on cut position and dimensional accuracy. The machine is equipped with a mist-extraction system that promptly removes mist and debris generated during cutting.
Интеллектуальное управление натяжением. The system adjusts diamond wire tension in real time according to cutting conditions and supports both constant-tension and variable-tension modes. This keeps the wire running stably, reduces trajectory deviation and wire breakage caused by tension fluctuation, and limits localised fluctuation in cutting load attributable to unstable wire travel — all of which contribute to better control of slice quality.
Запоминание обрыва проволоки. Если алмазная проволока порвется или станок остановится аномально, the system automatically records the current machining position and associated operating state. После замены проволоки, cutting can resume from the recorded position. This reduces repositioning error and its effect on trajectory and dimensional accuracy, lowers material loss and quality variation from repeated machining, and improves yield.
High-rigidity one-piece cast iron frame. The one-piece cast iron frame increases overall stiffness and vibration resistance, reducing structural vibration and deformation during operation and their effect on wire trajectory, while also damping fluctuation in cutting force. The stable mechanical structure helps prevent uneven local loading of the PV panel during cutting.
4. Process Parameters and Cooling Method
| Параметр | Значение |
|---|---|
| Диаметр проволоки (миллиметр) | 0.50 × 1930 |
| Wire traverse speed (мм/мин) | 20 |
| Ширина реза (миллиметр) | 20 |
| Напряжение проволоки (N) | 220 |
| Скорость проволоки (М / сек) | 26 |
| Wire bow time (s) | 100 |
| Нагрузка при резке (Н·м) | 27 |
5. Cutting Performance and Results
5.1 Данные теста TTV (Единица: миллиметр)
Изменение общей толщины (TTV) измерялся с использованием сетки из девяти точек, dual-probe thickness gauging method on a vacuum-chuck stage. The measurement was applied to PV panel wafers produced by ring diamond wire cutting. The nominal specimen thickness was 10.000 миллиметр.
| Образец | Nine-point thickness readings | Tmax | Tmin | TTV |
|---|---|---|---|---|
| S01 | 9.904, 9.906, 9.908 9.907, 9.909, 9.910 9.908, 9.909, 9.911 |
9.911 | 9.904 | 0.007 |
| S02 | 9.917, 9.919, 9.920 9.918, 9.921, 9.922 9.919, 9.920, 9.923 |
9.923 | 9.917 | 0.006 |
| S03 | 9.932, 9.934, 9.935 9.934, 9.936, 9.937 9.935, 9.936, 9.939 |
9.939 | 9.932 | 0.007 |
| S04 | 9.929, 9.931, 9.932 9.931, 9.934, 9.935 9.932, 9.934, 9.937 |
9.937 | 9.929 | 0.008 |
Assessment. Across the four PV panels, measured thicknesses fell within 9.904–9.911 mm (S01), 9.917–9.923 mm (S02), 9.932–9.939 mm (S03), and 9.929–9.937 mm (S04). TTV values ranged from 0.006 мм до 0.008 миллиметр, confirming that the ring diamond wire process holds total thickness variation within a tight band across all four samples.
5.2 Данные по допуску толщины (Единица: миллиметр)
Thickness tolerance was measured using the same nine-point grid method, с 10.000 mm taken as the nominal thickness of the PV panel wafer. The deviation of each measured point from nominal was calculated, и максимальное положительное отклонение, максимальное отрицательное отклонение, and overall thickness deviation range were determined in order to evaluate thickness consistency of the sliced wafers.
| Образец | Mean thickness | Thickness deviation |
|---|---|---|
| S01 | 9.908 | −0.092 |
| S02 | 9.920 | −0.080 |
| S03 | 9.935 | −0.065 |
| S04 | 9.933 | −0.067 |
| Максимальное положительное отклонение | — | −0.065 mm |
| Максимальное отрицательное отклонение | — | −0.092 mm |
| Thickness tolerance band | — | ±0.014 mm |
Assessment. Against a nominal thickness of 10.000 миллиметр, the four PV panels showed mean thicknesses of 9.908–9.935 mm and thickness deviations of −0.092 to −0.065 mm, all on the negative side. S01 showed the largest deviation and S03 the smallest. The overall thickness tolerance band was ±0.014 mm, indicating good repeatability of slice thickness across the batch.
5.3 Данные по шероховатости поверхности Ra (Единица: мкм)
Шероховатость поверхности (Ra) was measured by stylus profilometry on PV panel wafers after ring diamond wire cutting. Three representative positions — centre, середина-слева, and mid-right — were profiled along the cut end face, and the surface roughness parameter Ra was recorded at each position.
| Образец | Ra-1 | Ra-2 | Ra-3 | Mean Ra |
|---|---|---|---|---|
| S01 | 0.72 | 0.81 | 0.76 | 0.76 |
| S02 | 0.65 | 0.71 | 0.68 | 0.68 |
| S03 | 0.58 | 0.64 | 0.61 | 0.61 |
| S04 | 0.69 | 0.77 | 0.73 | 0.73 |
Assessment. Mean Ra across the four samples ranged from 0.61 μm to 0.76 мкм, with all individual readings between 0.58 μm and 0.81 мкм. The consistency of Ra across the three measurement positions on each wafer indicates a uniform surface finish along the cut face, which is characteristic of stable single-direction ring wire cutting.
5.4 Edge Chipping Data (Единица: мкм)
Edge chipping was quantified by optical imaging on a toolmaker’s microscope. The nominal specimen thickness was 10 миллиметр. Specimen edges were cleaned before measurement, and chipping at the cut edge was measured at four positions per sample, with the maximum chipping value recorded.
| Образец | Положение 1 | Положение 2 | Положение 3 | Положение 4 | Макс. сколы |
|---|---|---|---|---|---|
| S01 | 8.2 | 9.6 | 10.4 | 11.1 | 11.1 |
| S02 | 6.4 | 7.2 | 8.1 | 7.5 | 8.1 |
| S03 | 5.1 | 6.3 | 5.8 | 7.0 | 7.0 |
| S04 | 6.8 | 8.5 | 7.6 | 9.2 | 9.2 |
Assessment. Four-point edge inspection of the four PV panel wafers (S01–S04) gave maximum chipping values of 11.1, 8.1, 7.0, и 9.2 μm respectively, with all measurement points falling within 5.1–11.1 μm. S03 showed the smallest maximum chipping (7.0 мкм). The results indicate that edge integrity is maintained within a narrow band across the batch.
6. Заключение
The process control applied in this high-precision slicing trial of solar photovoltaic panels centred on three elements: a purpose-matched cutting machine, water-based cooling, and correctly matched cutting parameters. PV panel stock places specific demands on machine running stability, cutting trajectory, and slice dimensional control, and generates localised stress during cutting that must be managed to preserve edge quality.
Equipment. An ESO-GM ring diamond wire cutting system with a gantry-type cutting structure was used. The gantry configuration provides high overall rigidity and running stability, giving the diamond wire a reliable mechanical basis for continuous travel and trajectory control. Stable machine motion is a prerequisite for consistent slice thickness and surface quality.
Охлаждение. Water-based cutting was adopted. During cutting the diamond wire remains in continuous contact with the workpiece and removes material by abrasion, generating heat and debris in the cutting zone. Water cooling limits localised temperature rise, carries away part of the debris, and helps suppress thermal damage and chipping at the cut edge.
Process parameters. Скорость проволоки, Норма подачи, and other key parameters were matched to the machining requirements of PV panel stock and to the target slice thickness. Parameter settings were chosen to maintain stable wire travel and continuous material removal, avoiding excessive feed rates that would raise cutting load and degrade surface finish and edge quality.
Overall. Taken together — slice dimensional accuracy, thickness tolerance, шероховатость поверхности (Ra), and cut-edge quality — the coordinated use of a gantry-type purpose-built cutting machine, water-based cooling, and appropriate process parameters provides effective control of high-precision straight slicing of solar photovoltaic panels. This process combination improves dimensional consistency, Обработка поверхности, and edge integrity of PV panel wafers, and offers a reliable route for precision slicing of photovoltaic material.
